Residential - Blog

April 2021
Magnetic Water Treatment: Fact, Fiction, or Unknown?


Magnetic Water Treatment 

Living in a hard water area can be a big pain for many homeowners. Not only does hard water cause aesthetic issues such as hard-scale buildup on home fixtures, but it also forces homeowners to spend money on servicing and/or replacing their appliances. For example, replacing a heating element in a household appliance, such as a water heater, can cost hundreds of dollars.
These hard water hassles cause many home and/or business owners to look for solutions to protect their properties and their wallet without having to use a traditional salt-based water softener. There are many alternative water treatment options in the market for the average consumer to choose from. With all of these options, how does one know which solution will be the right choice?

Below we will explore the various types of magnetic water conditioners available on the market today, and the science behind why they may or may not work well to prevent hard scale.

How Do Magnetic Water Conditioners Prevent Scale?

Let us start with how magnetic water conditioners work to prevent scale. As more people look to move away from traditional salt-based water softeners to various salt-free options for their drinking water they will come across various magnetic devices. Magnetic water conditioners are devices intended to prevent the build-up of hard limescale in a physical (e.g. non-chemical) manner. This is done by influencing the ions in the water using a magnetic field so that when the saturation point of the water is altered (e.g. by heating) the calcium carbonate (or other minerals) precipitates as small crystals in suspension in the water, rather than as a solid mass bonded to surfaces such as pipes and heating elements. Do magnetic water conditioners work? In short yes, however not nearly as well as other methods due to their low power. Next, we will look at specific types of magnetic water conditioners and their pros and cons. 




Types of Magnetic Water Treatment Devices


Intrusive Magnets 

Intrusive magnets were the first physical water conditioners that appeared after the discovery that water flowing over magnetic rock did not cause hard scale to accumulate on the rock's surface. 



Magnetic water treatment
Figure 1: Intrusive Magnet


Figure 1: illustrates the general principles that are employed in the operation of intrusive magnets. The conductors represent the water that is moving and cutting the magnetic lines, thus generating a voltage represented by the (+) and (-) on the ends of the conductors. The voltage that can be generated by utilizing such an arrangement depends on the strength of the magnet and the speed of the flow of the water. 


Current is generated as a result of the voltage. The current will be dependent on the voltage and the conductivity of the water. The current that is produced by this method is DC (Direct Current). It will act as a galvanic current causing corrosion and will release metal ions into the water. 


Any clusters that are formed due to the electrical field near the magnets will be carried by the water flow towards the source of heat. Some clusters will grow by attracting more ions and some will dissolve back. These clusters are not stable and will break up to individual ions after a relatively short time (2-3 min). If enough clusters can reach the source of heat they will grow to form a nuclei and the crystallization will occur as described above. 


This dependence on the rate of flow and conductivity of the water can cause unreliable results when utilizing this conditioning method. In addition, a permanent magnet will attract magnetic particles flowing in the water, causing reduced efficiency and increasing the possibility of complete obstruction of the pipe. No enhanced nucleation can occur beyond the magnet itself, as the effect is localized to the magnet. 


When used on plastic pipes, magnets have no effect because the electric field cannot be formed without the metal path for the current to flow. In industrial circulating systems a small degree of success can be achieved.


Clamp-On Magnets 

These are constructed mainly of ceramic magnets that are plastic coated. Two individual magnets are clamped on the pipe to create the magnetic lines. These are attenuated by the large air gap between the magnets. There is no way to control the speed of flow of the water and there is no reliable scientific evidence to prove that benefits claimed are being produced. 


It is debatable if such an arrangement can generate an electric field capable of forming clusters. Manufacturers producing such devices claim that results can be achieved with any pipe material, however, without scientific evidence, there is no way to verify if that is a legitimate statement.



With the correct design, it is possible to generate strong magnetic fields with electromagnets. Electromagnets are much like clamp-on magnets, only considerably stronger. It is also possible to control the speed of flow by restricting the flow. These devices suffer the same disadvantages as the permanent intrusive magnets described above. An additional disadvantage is that they must be connected to an electrical source, resulting in installation and running costs. The only advantage of electromagnets over permanent magnets is the ability to be switched off, thereby releasing any magnetic particles that may have accumulated in the pipe.


Non-Intrusive Electromagnets

These are categorized by wires that are wrapped around water pipes in an attempt to generate a magnetic field. The 60 Hz coils are carrying the voltage to a single wire coiled around the pipe.                                                                                                                                                                                                                                           

Figure 2: Magnetic field lines produced by a non-intrusive electromagnet

Figure 2 illustrates a section of pipe and the coil wound around it. The red magnetic lines running parallel to the moving fluid will generate little to no electrical field. Some magnetic lines beyond the ends of the coil flow between the poles and will cut the liquid at shallow angles. This will generate weak electric fields at both ends of the coil. In practice due to the uneven distribution of the magnetic lines, the voltages do not cancel completely.


There are other reasons for variation in the electric field that may be formed by this method. The main one is the turbulence of the water flow within the pipe. The water flow within a pipe may not flow linearly. This depends on many factors and will be completely different between one installation and another. The turbulent flow within the axial magnetic lines will cause uneven voltages within the electromagnet. These variable conditions can explain the reason that in some cases these devices have some success and in others, they fail completely.


Electrolytic Water Treatment

Electrolytic physical water conditioners are basically a battery. These water conditioners operate on the well-known principle that if metal electrodes, made from different materials e.g. zinc and copper, are immersed in an electrolyte; between them, Zinc ions are then released into the electrolyte (water) by the anode. The release of positive zinc ions into the water will release electrons that will flow to the copper cathode through the connecting wire. This process will continue until the zinc anode is completely dissolved. 


The electrodes are connected by a large resistor 1MΩ (1,000,000 Ohms). This is done to increase the life of the zinc anode but will drastically reduce the electrical field applied to the water. The manufacturer is faced with the problems of increased conditioning effect at the expense of the life of the conditioner. A balance must be achieved. A reasonable life span is only obtained with the conditioning effect reduced. 


It is generally accepted that these conditioners are producing an effect. And, as there is solely an electrical field being generated (no magnetic field) to obtain scale inhibiting, this is additional proof that the electrical field is responsible for the conditioning effect as described above. There are numerous disadvantages with such conditioners:


  • The life of the conditioner cannot be determined. It is affected by the conductivity of the water that varies considerably from area to area.  
  • As the anode is exhausted the conditioning effect will stop. Damage to expensive appliances may result. 
  • Zinc ions are released into the drinking water. 
  • Regular and expensive maintenance must be performed to ensure reliable results. 
  • The conditioning effect can only be transported by the flow of water.


Magnetic Wire Coils

There are numerous manufacturers of the wire coil electromagnet physical water conditioners. All are based on two basic designs:


  • One coil is wrapped around the pipe and is connected to the signal generator.
  • Two coils are wrapped around the pipe, one end of each coil is connected to the signal generator, and the other end is left open.

Note: Dutch and Belgian inventors have patented both designs respectively, however, many copies of these designs have been in production for the past 20 years without any apparent difficulty. 


In general, they produce the same swept-frequency square wave signal of 1 kHz to 6 kHz. Various designs have appeared in the amateur electronic press. For example, in Elektor Electronics international electronic magazine issue July/August 1994, an article headed “Water Softener”, describes in detail the construction of such circuitry with single, double, and triple coil systems. In a single coil system, the inductance of the coil is very low. The information below illustrates how you would test for signal strength in this type of system.


  • To be able to view the output signal it is necessary to disconnect one end of the coil from the signal generator. In a single coil system, the voltage may be 4V peak to peak (p to p) and the frequency may be between 5-6 kHz. This is the top frequency.
  • Connect the coil back to the signal generator. The voltage may be 15 mV peak to peak. The frequency may be between 240 Hz and 6 kHz. The drastic reduction in output is due to the large load that the small inductance is exerting on the signal generator.
  • Measure the signal on the pipe and you will see the voltage of 1mv peak to peak. This is the highest level of signal pulses that this type of system is able to induce into the water. The energy that is produced by an oscillating electrical signal is the R.M.S. value or the equivalent D.C voltage that will produce the same energy.


Why Magnetic Water Treatments Don’t Work?
The common theme of the above devices is their low power output, and ability to only treat the water at the point the magnet is installed. Once the water flows past the magnet the effects begin to wear off immediately, only lasting a couple of minutes. This means without constant flow the water is not being effectively treated before it hits the point of scaling out. Even with constant flow, the low power output of these devices has a very limited effect, and oftentimes hard scale remains a problem in the system. 

In conclusion, magnetic water treatments are simply another type of physical water conditioner. Albeit not very effective it still centers around the same principle of having an effect on the pre-nucleate calcium carbonate clusters at the moment of precipitation.


magnified hard scale

Figure 3a: Untreated hard water - calcite crystal formations (hard scale)


Aragonite and Vaterite crystals

Figure 3b: Physical water conditioner treated water - crystal formations (aragonite and vaterite)


Figure 3a and 3b are both microscopic pictures of calcium carbonate. As you can see water treated with a physical water conditioner has a huge impact on how the calcium crystals form. The crystals on the top image (Figure 3a) form hard scale and will attach to your pipes and equipment. The crystal formations in the bottom image (Figure 3b) will not attach to your pipes and equipment and are sometimes referred to as soft scale.



Hydropath Technology

The HydroFLOW conditioner, which is powered by Hydropath technology, is a sophisticated signal generator that produces a complex waveform. This waveform is fed to a ferrite core. In the residential range, the core is divided into two sections that are pressed together by a leaf spring. In the commercial and industrial units, the core is constructed in segments. It is within this core that the oscillating coaxial magnetic field (O.C.M.F) is generated. The O.C.M.F. induces a voltage in the pipe and the water in the pipe. These two voltages are the same. Since there is no voltage difference between the liquid and the metal, no current can flow between them. This will eliminate any corrosion that would have otherwise formed. The frequency of oscillation is +/- 150 KHz.



Hydropath Signal
Figure 4: The Hydropath Signal


HydroFLOW has an advantage over other eco-friendly physical water conditioners because the patented Hydropath signal travels throughout the entire piping system, without the need for flowing water. All other generic types of water conditioners act on the water only at the installation point and are flow-dependent. It is necessary for the water to flow within the unit to transfer energy to the water. The flow must be slow enough to transfer the energy to the water. If it is too fast, not enough energy will be transferred to create the effect. If the flow is too slow it will take too long to reach the area where the minerals are precipitating, and the effect will decay in about 2-3 min. This is the reason that manufacturers specify flow rates, and maximum flow necessary for the proper operation of such devices. Such flow rates are unlikely to be achieved in practical applications. 


To prevent scaling, energy has to be transferred to the water to change the crystallization from the piping and equipment surfaces to suspension in the water. This is what happens with all the physical water conditioners on the market.


Hydropath technology works differently by applying energy efficiently throughout the plumbing system. The propagating electrical field creates clusters of ions everywhere and recreates the clusters that have been dissolved back into solution by the water.